Skip to Content

MARKING SPRAYS FOR LASERS - PRODUCTS FOR ADDITIVE LASER MARKING - PIGMENTUM GMBH

PERMANENT MARKINGS - THROUGHOUT THE ENTIRE PRODUCT LIFECYCLE

The markSolid laser marking material is applied in a thin layer to the surface and then chemically and physically bonded to the surface in a thermally activated process by the laser. The result: high-contrast markings on metal, glass, and ceramics in various colors, always with significantly reduced heat input into the component.

Discover more Contact

FOR THE LASERS YOU ALREADY HAVE

markSolid products are the link between the laser and the substrate to be marked. markSolid works for all lasers and gives your device new capabilities.

CO2

10.6 µm

LABEL ALL METALS, e.g. stainless steel faster and more durable than annealing markings with the fiber laser are possible, or create colored markings on glass and ceramic materials.


FIBER LASER

1,064 nm

NOW MARK GLASS AND CERAMICS in contrasting colors, chemically resistant and dishwasher safe. When conventional marking reaches its limits, produce a deep black marking on all metals with extremely high chemical and mechanical resistance.

DIODE LASER

400 nm - 900 nm

With markSolid, your diode laser becomes a superstar. Mark stainless steel and many other metals permanently and with perfect contrast. Glass and ceramic markings also work in color.


markSolid - LASER MARKING MATERIALS ARE


BRILLIANT AND RELIABLE

As an additive laser marking process, markSolid combines excellent contrast, best edge sharpness, and high resolution with maximum resistance to mechanical and chemical stresses as well as to UV light and high temperatures (>1,000°C).


PERMANENT AND COUNTERFEIT-RESISTANT

Often, it is necessary to withstand multiple load components simultaneously (e.g., outdoor or offshore, a combination of UV radiation, seawater, acid rain, snow and ice, or even sandstorms). markSolid laser markings also succeed here.

Since the marking chemically and physically bonds with the component, its removal or alteration is not possible without simultaneously causing significant damage to the component.


MATERIALS GENTLE

Typical for laser markings is the non-contact working method. Furthermore, the markSolid process also reduces the thermal stress on the substrate. Structural changes or warping in metal signs are significantly minimized, with no worries about rust formation when marking stainless steel. There is no material removal, and the marking does not become a predetermined breaking point – important when marking components with high safety relevance.

THE CLEARLY BETTER SOLUTION:

The markSolid process with its laser marking materials.

markSolid markings combine top results in durability, contrast, resolution, and marking speed at a low stress level for the component to be marked.

The additive marking process places only low demands on the marking laser and opens up diverse, new possibilities around the existing laser or the material itself (e.g., metal marking with the CO2 laser or colored markings on glass and ceramics with fiber lasers).

For special requirements, we customize markSolid laser marking materials or develop new solutions. 

markSolid - LASER MARKING MATERIALS ARE


BRILLIANT AND RELIABLE

As an additive laser marking process, markSolid combines excellent contrast, best edge sharpness, and high resolution with maximum resistance to mechanical and chemical stresses as well as to UV light and high temperatures (>1,000°C).


PERMANENT AND COUNTERFEIT-RESISTANT

Often, it is necessary to withstand multiple load components simultaneously (e.g., outdoor or offshore, a combination of UV radiation, seawater, acid rain, snow and ice, or even sandstorms). markSolid laser markings also succeed here.

Since the marking chemically and physically bonds with the component, its removal or alteration is not possible without simultaneously causing significant damage to the component.


MATERIALS GENTLE

Typical for laser markings is the non-contact working method. Furthermore, the markSolid process also reduces the thermal stress on the substrate. Structural changes or warping in metal signs are significantly minimized, with no worries about rust formation when marking stainless steel. There is no material removal, and the marking does not become a predetermined breaking point – important when marking components with high safety relevance.

THE CLEARLY BETTER SOLUTION:

The markSolid process with its laser marking materials.

markSolid markings combine top results in durability, contrast, resolution, and marking speed at a low stress level for the component to be marked.

The additive marking process places only low demands on the marking laser and opens up diverse, new possibilities around the existing laser or the material itself (e.g., metal marking with the CO2 laser or colored markings on glass and ceramics with fiber lasers).

For special requirements, we customize markSolid laser marking materials or develop new solutions. 

THREE STEPS TO FINISHED MARKING



Apply

Apply marking material thinly and evenly with a spray can, brush, airbrush, or roller. It dries in no time.



Laser

Under the laser, a physical and chemical bond is formed between the laser marking material and the substrate. This bond and the inorganic nature of the laser marking materials create highly durable permanent markings.



Wash off

Remove excess marking material, e.g., with water. The permanent marking remains.

OUR PRODUCTS

For permanent markings on all metals, anodized aluminum, glass, ceramics, and porcelain 
select first by material, then by application method and color.


markSolid

markSolid products are developed and manufactured in Germany

  • Black marking on metals

    markSolid 114 – Aerosol spray can
    markSolid 015 – for brush and airbrush

  • Black marking on anodized aluminum

    markSolid 904 – for airbrush

  • Colored marking on glass, ceramics, porcelain

    markSolid 501 - white – for airbrush
    markSolid 551 - blue – for airbrush
    markSolid 560 – green – for airbrush
    markSolid 590 – black – for airbrush

  • Black marking on sapphire (glass)

    markSolid 990 – black – for airbrush


Individual solutions

  • Your application - Your material.

    When standard products reach their limits, we develop the appropriate solution. In our product development in Stein near Nuremberg, we specifically tailor markSolid products to your substrate, your laser, and your process, made in Germany with 20 years of experience.

  • What we customize for you

Substrate

Special alloys, glazed ceramics, specialty glasses, and coated surfaces.

Application

Spray, paste, or airbrush, for manual or automated processes.

Laser parameters

Optimized for your laser type and your cycle time.

Color & Durability

Deep black or colored markings, resistant to UV light, dishwasher, aggressive chemicals, and environmental influences.

Cermark

Proven products from a traditional US brand

  • Black marking on metals

    LMM 6000 aerosol spray can
    LMM 6000 liquid/paste – for brush and airbrush

  • Black marking on anodized aluminum and other surfaces

    LMM 6018 transfer tape


markSolid 114

The most powerful metal marking product for stainless steel, all non-ferrous metals, and metallic coatings. Highest durability and high marking speeds even with lower-powered laser devices. Very efficient due to adjustable spray nozzle and simple application. Shake the can briefly, spray, done. Does not clog and no "upside-down spraying after use" needed.

300-ml spray can with flexHead spray nozzle

markSolid 015

Paste version of markSolid 114 with identical marking properties.

markSolid 904

Specifically for anodized aluminum. Economical for large demand or larger areas. Requires a one-time training for optimal laser settings and coating (very thin and even).

markSolid 501, 551, 560, 590

Colored products in paste form for glass, ceramics, enamel. Markings are dishwasher safe and resistant under challenging industrial conditions.

Cermark LMM 6000

A US product for many metals. For well-heat-conductive metal surfaces, more powerful lasers are better suited. After application, a grip-resistant coating is created, allowing the stacking of pre-coated signs. Available as an aerosol can and paste product.

Cermark LMM 6018

Transfer tape for all surfaces (metals, glass, ceramics), when spraying is not desired. Especially recommended for anodized aluminum with a short training time. Ideal for occasional needs and small areas.

markSolid 114 - high-performance metal marking product

TELL US MATERIAL AND LASER

Tell us the material, laser type, and your task. You will receive a specific product recommendation.

Colored marking on glass, ceramics, porcelain